iRobot Roomba 660 Vacuum Cleaner Manual

The iRobot Roomba 660 is a robotic vacuum cleaner designed to autonomously clean your floors. It features advanced navigation technology, a powerful suction system, and a variety of cleaning modes to ensure your home stays clean with minimal effort. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting to the App 7. Cleaning Modes 8. Maintenance 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Smart navigation, powerful suction, dual multi-surface brushes, dirt detection technology, and a scheduling feature.

Feature	Description
Smart Navigation	Uses sensors to navigate around furniture and obstacles.
Powerful Suction	Effectively picks up dirt, dust, and pet hair.
Dual Multi-Surface Brushes	Agitate and lift dirt from carpets and hard floors.
Dirt Detection Technology	Identifies areas with more dirt and focuses cleaning efforts there.
Scheduling Feature	Allows you to set cleaning times for convenience.

Installation

Unpack the Roomba and place it on a flat surface. Ensure the charging dock is plugged in and positioned against a wall.

Connect the charging dock to a power outlet.
Place the Roomba on the dock to charge for at least 3 hours before first use.
Remove any obstacles from the cleaning area.

WARNING! Ensure the charging dock is in a clear area to allow Roomba to navigate freely.

First-Time Setup

Power on the Roomba; follow the voice prompts to set up your device.

Press the CLEAN button to start the setup process.
Connect to the iRobot HOME App for additional features.
Set your cleaning schedule through the app.

CAUTION! Ensure the Roomba is on a stable surface during setup.

Specifications

Model: Roomba 660.
Dimensions: 13.9 x 13.9 x 3.6 inches.
Weight: 7.9 lbs.
Battery: Lithium-ion, 1800 mAh.
Run Time: Up to 90 minutes.
Charging Time: Approximately 3 hours.
Filter: HEPA-style filter.
Connectivity: Wi-Fi enabled for app control.

Controls and Settings

Access settings via the iRobot HOME App or use the physical buttons on the Roomba.

Buttons: CLEAN, SPOT, DOCK, and POWER.

Settings include scheduling, cleaning modes, and maintenance reminders.

Connecting to the App

Download the iRobot HOME App from your device's app store.

Open the app and create an account or log in.
Follow the prompts to connect your Roomba to Wi-Fi.
Customize your cleaning schedule and preferences in the app.

Tip: Ensure your smartphone is connected to the same Wi-Fi network as the Roomba.

Cleaning Modes

The Roomba 660 offers several cleaning modes:

Auto Mode: Cleans an entire room.
Spot Mode: Cleans a specific area.
Scheduled Cleaning: Cleans at set times.

WARNING! Do not use the Roomba on wet surfaces.

Maintenance

Regular maintenance is essential for optimal performance.

Empty the dustbin after each use.
Clean the brushes and filter monthly.
Check for any obstructions in the wheels and sensors.

CAUTION! Always turn off the Roomba before performing maintenance.

Regulatory Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Roomba does not charge	Charging dock not connected	Ensure dock is plugged in and Roomba is seated properly.
No suction	Full dustbin or clogged filter	Empty dustbin and clean filter.
Roomba gets stuck	Obstacles in the way	Clear the area of obstacles.
Remote not working	Batteries dead	Replace batteries in the remote.

Reset: Press and hold the CLEAN button for 10 seconds.

Service: Contact iRobot customer support for assistance.